What should I do if water enters the micro gas station tank?

Eight steps to deal with water entering the micro gas station tank

Bluesky best seller 3000 liters 3 nozzle with tank gauging system and printer.

micro gas station tank

Suspension of business

When water is found or suspected in the oil tank, the refueling operation of the “problem oil tank” should be stopped immediately. Before confirming whether the oil tank has water, it shall not be sold to the outside.

If the “problem oil” has been exported, the corresponding emergency response plan should be immediately activated to resolve the contradiction, eliminate the impact, and avoid the escalation of the situation.

Sedimentation

After confirming that the oil tank has water in it, the sedimentation time should be maintained for more than 8 hours to allow the water to fully settle to the bottom of the tank.

When the ethanol-gasoline tank enters the water body, due to its strong hydrophilicity, the oil very easily deteriorates. It is necessary to extract all the oil in the tank and organize the tank cleaning.

Measurement

After ensuring that the site is well guarded, use the oil dipstick and water gauge to manually measure the oil and water heights.

Water cutting

After the water layer is determined, the organization arranges to use hand pumps, explosion-proof sweeping pumps, etc. to pump out the water in the tank.

The extracted oil-water mixture must be sent to a designated location for treatment and cannot be discharged at will. When temporary electricity is required for tools used on site, an operation permit should be obtained.

Laboratory test

Based on the water height and oil height, take at least three samples from the top, middle, and bottom and send them to the inspection department for oil testing and analysis.

At the same time, observe the color of the oil and judge the impurities. Determine the oil-water stratification and emulsification according to the analysis results and deal with them separately.

Under normal circumstances, the possibility of emulsification of finished oil in a short period is extremely low, but because the water entering the tank area is usually dirty, the oil may contain a large amount of impurities. The oil in the tank inventory can only be sold after the quality inspection is qualified.

Transfer

When the oil product fails the inspection, arrange a tanker truck with appropriate capacity, equipped with explosion-proof pumps, filters, etc., to transfer the contaminated oil in the tank to the tanker truck and send it to the designated location for treatment. Filtering treatment is not allowed at the gas station.

Transfer the contaminated oil in the tank to the tank truck

Cleaning

If contaminated oil enters the process system such as the fuel dispenser, it should be cleaned in time. Use qualified oil to flush the fuel dispenser, submersible pump, and pipeline.

The flushing oil flows into the designated contaminated tank, and the flushing oil is filtered according to the contaminated oil to the tanker. The oil tanks that fail the oil test need to be cleaned.

The oil tank cleaning should be carried out according to the corresponding requirements and the operation permit should be obtained.

Treatment

Unqualified oil products, recycled oil, water cuts, and other oil-water mixtures recovered from various links shall be returned to the refinery and oil depot for disposal or treated accordingly as unqualified oil products if no other treatment measures are taken.

Layout of underground oil tanks

Precautions

(I) When water enters the oil tank

1. Take waterproof covering (plastic film, etc.) for the parts that may enter the water (operating well and its surrounding area), cut off the water source entering the oil tank, and prevent water from continuing to enter the tank.

For water that has entered the operating well, scoop water manually and wipe the operating well clean. If the amount of water is large, an explosion-proof pump can be used for pumping.

2. When handling at night, use explosion-proof flashlights and other lamps for lighting, and it is forbidden to privately pull wires for daily lighting.

3. When water or other impurities are mixed in the oil, the static charge will increase significantly. Anti-static measures must be implemented during operation to control the flow rate to less than 1m/s.

4. If the handling procedure involves non-routine operations, an operation permit should be obtained.

5. If there are other situations such as floating tanks and pipeline breaks, handle them according to relevant regulations.

(II) When oil overflows

1. Alert the surrounding areas of the gas station, draw safety warning tapes, arrange personnel for supervision, conduct flammable gas monitoring, and the gasoline monitoring interval does not exceed half an hour.

2. Control the spilled oil within the scope of the gas station, use fine sand to block it, and use oil ropes, oil absorbents, oil dispersants, and aluminum barrels to recover the spilled oil.

When the amount of spilled oil is large, it can be recovered with an explosion-proof sweeping pump. During the disposal process, explosion-proof tools must be used, and anti-static work clothes and shoes must be worn.

3. Prevent the oil from flowing out of the station to pollute the environment and cause fire or explosion accidents.

If the oil has flowed out of the station, it is necessary to track the flow direction and oil head, block it in time, and deal with the oil pollution to prevent the fire outside the station from “backfiring” inside the station.

When the spilled oil flows into the road, contact the traffic control department and prohibit vehicles from passing.

Update cookies preferences
WhatsApp

Get a Quick Quote!

x

    Get a Quick Quote!

    x